washer fluid SKODA FABIA 2000 1.G / 6Y Workshop Manual

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Table of ContentsEdition 09.04
S00.5301.14.20II
- Changing brake fluid (every 2 years)...............................................................
- Inspecting the brake fluid level ......................................................................
- Track rod ends: Inspect play, correct attachment and joint boots .............................
- Inspecting tyres (including spare wheel) ...........................................................
- Inspecting the tyre tread depth (including spare wheel) and entering ........................
- Tightening wheel bolts to specific torque ..........................................................
- Inspecting the tyre inflation pressure (including spare wheel) and correcting the tyre
inflation pressure if necessary .......................................................................
Electrical System.......................................................................................
- Power windows: Inspecting positioning ............................................................
- Electrical components: Check for proper operation ..............................................
- Battery: Testing no-load voltage ....................................................................
- Battery: Inspecting electrolyte level, topping up with distilled water if necessary ...........
- Radio: Check for proper operation..................................................................
- Setting clock ............................................................................................
- Connect vehicle system tester and interrogate fault memory..................................
- Resetting service interval display (SID) QG0 .....................................................
- Resetting service interval display (SID) QG1 and QG2 .........................................
- Changing the code of the service intervals ........................................................
- Inspecting headlight beam setting and adjusting if necessary .................................
- Setting the headlight beam ..........................................................................
- Replace emergency battery for alarm system ...................................................
Body.......................................................................................................
- Airbag units: Visual inspection ......................................................................
- Inspect key switch for deactivation of front passenger airbag ..................................
- Check underbody protection and body paintwork for damage .................................
- Inspecting plenum chamber and water drain openings for dirt, cleaning if necessary .....
- Windscreen wiper/washer system: Check for proper operation ................................
- Sun roof: Cleaning and greasing runners .........................................................
- Door locks, locking buttons, child safety locks: Check for proper operation .................
- Replacing the dust and odour filter element ......................................................
- Sticking the vehicle data sticker .....................................................................
- ................................................................................. Inspect trailer coupling
Exhaust-emission Analysis..........................................................................
- Exhaust-Emission Analysis on Models with Fuel Engines ......................................
- Test Values for Exhaust-Emission Analysis on Models with Fuel Engines..................
- Exhaust-Emission Analysis on Models with Diesel Engines ....................................
- Test Values for Exhaust-Emission Analysis on Diesel Engines................................
Miscellaneous...........................................................................................
- Tow starting/Towing ..................................................................................
- Perform a test drive ...................................................................................
- Raising the vehicle ....................................................................................02-5page 2
02-5page 4
02-5page 5
02-5page 5
02-5page 6
02-5page 6
02-5page 6
02-6page 1
02-6page 1
02-6page 1
02-6page 1
02-6page 2
02-6page 2
02-6page 2
02-6page 3
02-6page 4
02-6page 7
02-6page 9
02-6page 10
02-6page 12
02-6page 13
02-7page 1
02-7page 1
02-7page 2
02-7page 2
02-7page 3
02-7page 3
02-7page 4
02-7page 4
02-7page 5
02-7page 6
02-7page 6
02-8page 1
02-8page 1
02-8page 2
02-8page 5
02-8page 6
02-9page 1
02-9page 1
02-9page 2
02-9page 2

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 1 02
02-2 Inspection
Pre-Delivery Inspection -PDI- (Export)
The operations marked with * apply to all countries; other
operations are applicable to certain countries only!
Compare as-delivered condition of vehicle with order form Chapter
♦Engine fitted
♦Type plate in the engine compartment
♦Vehicle data sticker (compare with stamped identification number)
♦Colour of paintwork, badges, inscriptions
♦Seats (cover, colour) interior trim (colour)
♦Radio, speakers, aerial
♦Central locking system, anti-theft alarm system
♦Wheels, tyres
♦Sun roof
♦Vehicle log book - for completion: Operating manual and service plan (in the correct lan-
guage and with the correct edition data), short introduction, technical data, support in the
case of a breakdown, other manuals (radio,...) ) - all in the vehicle log book pouch
♦Other equipment (all equipment fitted in proper condition)
* Check transport damage (bodywork, paintwork, upholstery, interior trim, carpeting, footmats,
tyres, wheels)02-5, 02-7
Vehicle (exterior)
–Check that all car keys and key number fobs have been provided; check that the sticker
for the key number for the electronic immobiliser is complete and legible
–Proper operation of door handles outside, door locks, child safety locks, door contact
switches and proper operation of all locks and keys (including spare keys), doors, boot lid/
tailgate, fuel filler cap, bonnet lock02-7
–Proper operation of anti-theft alarm system
Engine compartment (from above)
–Check battery no-load voltage, recharge battery if necessary02-6
–Check tight connection of electric cables and plug connections (in particular battery ca-
bles)
–Inspect engine, gearbox, cooling system, brake system and fuel system for leaks02-3, 02-5
–Engine oil level (in-between markings on dipstick)02-3
–Brake fluid level (at „MAX“ marking)02-5
–Coolant level (in-between marking), special equipment antifreeze down to -35°C02-3
–Fill up fluid in washer reservoir, in the winter add antifreeze
Vehicle interior
–Proper operation of seat belts, seat belt height adjuster, power windows and sun roof
–Check car tool kit, spare wheel and accessories for completeness and proper attachment
Underside of vehicle (on lift platform)
–Inspect underbody (underbody protection for damage)02-7
–Inspect for leaks and damage: Engine, gearbox, final drive, steering, brake system, axles,
joint boots. Check proper routing of the brake hoses and brake lines, fuel lines including
ventilation of the fuel system02-3, 02-5

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 2 02
Pre-sales Inspection - (the Czech Republic)
Compare as-delivered condition of vehicle with order form Chapter
♦Engine fitted
♦Type plate in the engine compartment
♦Vehicle data sticker (compare with stamped identification number)
♦Colour of paintwork, badges, inscriptions
♦Seats (cover, colour) interior trim (colour)
♦Radio, speakers, aerial
♦Central locking system, anti-theft alarm system
♦Wheels, tyres
♦Sun roof
♦Vehicle log book - for completion: Operating manual and service plan (in the correct lan-
guage and with the correct edition data), a list of dealers, short introduction, technical da-
ta, other manuals (radio......) ) - all in the vehicle log book pouch
♦Other equipment (all equipment fitted in proper condition)
♦Vehicles in stock for more than 6 months: Change brake fluid
Inspections and operations to be completed
Vehicle (exterior)
–Plastic and rubber parts - cleanliness and damage
–Inspect bodywork and paintwork for damage02-7
–Check that all car keys and key number fobs have been provided; check that the sticker
for the key number for the electronic immobiliser is complete and legible
–Proper operation of door handles outside, door locks, child safety locks, door contact
switches and proper operation of all locks and keys (including spare keys), doors, boot lid/
tailgate, fuel filler cap, bonnet lock02-7
–Proper operation of anti-theft alarm system
–Tighten the wheel bolts to specified torque (steel and light alloy wheels 120 Nm), fit wheel
caps02-5
–Check the tyre inflation pressure (including spare wheel), if necessary correct the tyre in-
flation pressure, fit valve caps02-5
–Fit roof aerial
Engine compartment (from above)
–Check battery no-load voltage, recharge battery if necessary02-6
–Check tight connection of electric cables and plug connections (in particular battery ca-
bles)
–Inspect engine, gearbox, cooling system, brake system and fuel system for leaks02-3, 02-5
–Engine oil level (in-between markings on dipstick)02-3
–Brake fluid level (at „MAX“ marking)02-5
–Coolant level (in-between marking)02-3
–Fill up fluid in washer reservoir, in the winter add antifreeze
–Windscreen wiper/washer system and headlamp cleaning system: Check for proper oper-
ation02-7
Vehicle interior

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 4 02
–Fit roof aerial
Engine compartment (from above)
–Check battery no-load voltage; recharge if necessary02-6
–Check tight connection of electric cables and plug connections (in particular battery ca-
bles)
–Brake fluid level (at „MAX“ marking)02-5
–Check the engine oil level (to be in-between the marking on the dipstick)02-3
–Check the coolant level (in-between marking), for special equipment antifreeze down to -
35 °C02-3
–Fill up fluid in washer reservoir, in the winter add antifreeze
–Check windscreen wiper and washer system, the spray nozzle adjustment and the resting
position of the windscreen wipers02-7
Vehicle interior
–Inspect upholstery, interior trim, carpeting and footmats for cleanliness and damage
–Inspect all switches, all electrical components, gauges/indicators and controls02-6
–Radio: Inspect for proper operation, store stations, encode, set clock02-6
–Fit net in luggage compartment (if available)
–Vehicle log book - for completion: Operating manual and service plan (in the correct lan-
guage and with the correct edition data), short introduction, technical data, support in the
case of a breakdown, other manuals (radio,...) ) - all in the vehicle log book pouch
–Reset service interval display02-6
–Power windows: Inspecting positioning02-6
–Key switch for airbag deactivation, front passenger side: Check function „ON/OFF“ and
switch-over to the position „ON“02-7
Underside of vehicle (on lift platform)
–Inspect underbody (underbody protection for damage)02-7
–Inspect for leaks and damage: Engine, gearbox, final drive, steering, brake system, axles,
joint boots. Check proper routing of the brake hoses and brake lines, fuel lines including
ventilation of the fuel system02-3, 02-5
–Inspect tyres and wheels for damage02-5
Concluding operations
–Perform a test drive02-9
–Interrogate fault memory of all systems, if necessary erase02-6
–Complete the service schedule, affix the vehicle data sticker in the Service Schedule to
the floor of the luggage compartment next to the spare wheel, complete the „Next Service
Date“ sticker and affix to the side of the dash panel on the driver's side02-7
–Remove recharging table (if affixed)
–Remove protective seat covers
–Install the carpets supplied in the vehicle
–Final inspection to ensure proper condition for handover to customer

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 6 02
Every 30 000 km (QG0)
Includes: Annual inspection and additional operations stated in the table below
–Track rod ends: Inspect play and correct attachment of boots
–Check the tyre inflation pressure (including spare wheel), correct if necessary02-5
–Inspect tyre wear (including spare wheel)02-5
–Inspect tyre tread depth (including spare wheel) and record (FL..., FR..., RR..., RL...,
SP...)02-5
–Inspect exhaust system for leaks, damage and attachment
–Brake fluid volume: Check level, if necessary top up02-5
–Battery: test02-6
–Check the anti-freeze in the cooling system and record ...... °C, check for leaks, top up
coolant if necessary02-3
–Flap lock for the engine bonnet: grease
–Inspect operation of all switches, all electrical components, gauges/indicators and con-
trols for proper operation02-6
–Windscreen wiper and washer system: Inspect condition of wiper blades, wiper opera-
tion, washer system: if necessary top up fluid02-7
–Inspect plenum chamber for dirt, clean if necessary02-7
–Fuel filter: Drain away water (vehicles with diesel engine with fuel operation, which does
not comply with DIN EN 590-standard)02-3
–Inspect trailer coupling (with removable arm - manufacturer Profsvar)02-7
After each inspection
–Complete the „Next Service“ sticker and affix sticker to the side of the dash panel (on the
driver's side)
–Perform road test including inspection of proper operation of footbrakes and handbrake,
gearshift and steering, final inspection02-9
–„Mirror tag“ - complete and attach to interior mirror
–Hand customer the completed and signed form
Work involvedChapter
–Headlights: Inspect, if necessary adjust02-6
–Gear oil: Inspect level and top up if necessary (manual gearbox)02-4
–Fuel filter: Drain away water (vehicles with diesel engine with fuel operation, which does
not comply with DIN EN 590-standard)02-3
–Check underbody protection and body paintwork for damage02-7
–Dust and odour filter element for the passenger compartment: replace02-7
–Inspect operation of tilting roof and grease the runners02-7
–Inspect timing belt (petrol engines) - every 90 000 km, then every 30 000 km02-3

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
InspectionEdition 09.04
S00.5301.14.2002-2 page 9 02
–Check the tyre inflation pressure (including spare wheel), correct if necessary02-5
–Inspect tyre wear (including spare wheel)02-5
–Inspect tyre tread depth (including spare wheel) and record (FL..., FR..., RR..., RL...,
SP...)02-5
–Inspect exhaust system for leaks, damage and attachment
–Brake fluid volume: Check level, if necessary top up02-5
–Battery: test02-6
–Check the anti-freeze in the cooling system and record ...... °C, check for leaks, top up
coolant if necessary02-3
–Flap lock for the engine bonnet: grease
–Inspect operation of all switches, all electrical components, gauges/indicators and con-
trols for proper operation02-6
–Windscreen wiper and washer system: Inspect condition of wiper blades, wiper operation,
washer system: if necessary top up fluid02-7
–Inspect plenum chamber for dirt, clean if necessary02-7
–Inspect operation of tilting roof and grease the runners02-7
–Headlights: Inspect, if necessary adjust02-6
–Gear oil: Inspect level and top up if necessary (manual gearbox)02-4
–Draining the fuel filter (diesel engine)
–Inspect trailer coupling (with removable arm - manufacturer Profsvar)02-7
–Check underbody protection and body paintwork for damage02-7
–Dust and odour filter element for the passenger compartment: replace02-7
–Air filter: Clean the housing, replace the insert every 4 years or 60.000 km.02-3
–Replace the fuel filter (diesel engine with fuel operation, which does not comply with DIN
EN 590-standard)
–Ribbed V-belt: Inspect condition and for vehicles without tensioning pulley also the ten-
sion - every 60.000 km02-3
–Replace the fuel filter (diesel engine) - every 60.000 km
–Spark plugs: replace - every 60.000 km.02-3
–Automatic gearbox: Check the ATF level, and top up if necessary, every 60.000 km
–Check the timing belt for the camshaft on a 4-cylinder petrol engine at 90.000 km and
then every 30.000 km after that
–Replace the emergency battery for the alarm system - every five years02-6
After each inspection
–Complete the „Next Service“ sticker and affix sticker to the side of the dash panel (on the
driver's side)
–Perform road test including inspection of proper operation of footbrakes and handbrake,
gearshift and steering, final inspection02-9
–„Mirror tag“ - complete and attach to interior mirror
–Hand customer the completed and signed form Work involvedChapter

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
BodyEdition 09.04
S00.5301.14.2002-7 page 3 02
The materials and the corresponding work instructions
are listed in the ⇒Technical Service Handbook, Part 6 -
Technology of paint repairs, chemical materials.
Inspecting plenum chamber and water
drain openings for dirt, cleaning if neces-
sary
Carry out a visual inspection for soiling through the cover
of the plenum chamber -arrows-. Remove the cover if it is
necessary to clean the plenum chamber (repair meas-
ure).
The water drain openings must not be blocked with wax
or underbody sealant.
Windscreen wiper/washer system:
Check for proper operation
Fluid in windscreen washer fluid reservoir
The fluid reservoir for the windscreen washer system
must be filled up to the brim.
♦If it is necessary to add fluid, always mix windscreen
cleaner to the water (in summer) or antifreeze agent
(in the winter).
♦If the vehicle is fitted with a headlight washing system
and the headlights have plastic - (polycarbonate) -
lenses, one must only use fluids for topping up the
headlight washing system which do not damage the
polycarbonate.
Inspecting setting of nozzles of windscreen
washer system, adjusting nozzles if necessary:
Nozzles of windscreen washer system
The nozzles on the windscreen washer system are set by
the manufacturer and cannot be subsequently altered.
–The water spray should strike the windscreen in a
cone-shaped pattern.
If the spray flows out unevenly, replace the spray nozzle
(repair measure).
Windscreen wiper arms: Inspecting park posi-
tion, adjusting if necessary
–Wiper arms are positioned relative to the round mark-
ings in the windscreen.
S02-0298
Note
Note
S02-0300
Note